RUBBER TECHNOLOGY
RUBBER TECHNOLOGY SYLLABUS
(These syllabus may change from time to time. Please check with the relevant Public Service Commission websites for any changes in the syllabus)
Rubber Products and Manufacturing techniques:
Manufacturing techniques of various tyres like two wheeler and car tyres, truck tyres, OTR, farm tyres, aircraft tyres, tyre related products like tubes, flaps, bladders, valves their design and manufacturing Reinforcement of elastomers by fillers. Factors influencing reinforcement and mechanism of reinforcement. Compounding and manufacture of cycle tyres and tubes, solid tyres, mechanical seals, sports goods, surgical products and miscellaneous moulded, extruded and calendered rubber products. Compounding techniques and manufacturing methods for the production of foot wears, conveyor and power transmission belts, hoses and tubing, rubber covered cables and wires, cellular rubber products and hard rubber products, tank, pipe and valve lining, shock absorbers and anti vibration mountings.
Rubber Products and Manufacturing techniques:
Manufacturing techniques of various tyres like two wheeler and car tyres, truck tyres, OTR, farm tyres, aircraft tyres, tyre related products like tubes, flaps, bladders, valves their design and manufacturing Reinforcement of elastomers by fillers. Factors influencing reinforcement and mechanism of reinforcement. Compounding and manufacture of cycle tyres and tubes, solid tyres, mechanical seals, sports goods, surgical products and miscellaneous moulded, extruded and calendered rubber products. Compounding techniques and manufacturing methods for the production of foot wears, conveyor and power transmission belts, hoses and tubing, rubber covered cables and wires, cellular rubber products and hard rubber products, tank, pipe and valve lining, shock absorbers and anti vibration mountings.
RUBBER TECHNOLOGY MCQs
1. The role of silicon emulsion in rubber product manufacturing is as a
A:-Froathing agent
B:-Mould releasing agent
C:-Dispersing agent
D:-Plasticiser
Correct Answer:- Option-B
2. Magnesium ammonium sulphate is otherwise known as
A:-Slurry
B:-Serum
C:-Sludge
D:-None of the above
Correct Answer:- Option-C
3. Hardness is measured in
A:-MPa
B:-N/mm
C:-Shore A
D:-Poise
Correct Answer:- Option-C
4. Tripsometer is an instrument used to determine
A:-Abrasion resistance
B:-Cure time
C:-Rebound resilience
D:-Compression set
Correct Answer:- Option-C
5. Rubber hydrocarbon content of whole tyre reclaim
A:-50%
B:->50%
C:-<50%
D:-0%
Correct Answer:- Option-A
6. EBC is a form of
A:-Crumb rubber
B:-Crepe rubber
C:-Special purpose rubber
D:-Block rubber
Correct Answer:- Option-B
7. Which of the following property is best in mono-sulphidic vulcanisation systems?
A:-Heat resistance
B:-Fatigue resistance
C:-Tensile strength
D:-Modulus
Correct Answer:- Option-A
8. Schwratz value is a quality assessment of
A:-Latex foam
B:-Balloons
C:-Sponge
D:-Latex thread
Correct Answer:- Option-D
9. Which among these is not considered as a quality control test for latex?
A:-VFA
B:-N2 content
C:-Sludge content
D:-Ammonia content
Correct Answer:- Option-B
10. The equipment used for preparing dispersion
A:-Bal mill
B:-Ultrasonic mill
C:-Attrition mill
D:-All the above
Correct Answer:- Option-D
11. Identify the additive used as white pigment
A:-Titanium di oxide
B:-Clay
C:-Whiting
D:-Carbon black
Correct Answer:- Option-A
12. Metrolac is an equipment used to determine the
A:-TSC
B:-DRC
C:-MST
D:-VFA
Correct Answer:- Option-B
13. Which among these cannot be considered as a general purpose rubber?
A:-Styrene butadiene rubber
B:-Chloroprene rubber
C:-Butyl rubber
D:-Poly butadiene rubber
Correct Answer:- Option-A
14. Potassium Oleate is added to the latex compound to
A:-improve the tackiness
B:-increase the viscosity of latex
C:-stabilize the latex
D:-cheapen the latex
Correct Answer:- Option-C
15. Butyl rubber is cured with
A:-Sulphur
B:-Peroxides
C:-Metal oxides
D:-Dioximes
Correct Answer:- Option-D
16. Which of the following is not a quality test for latex foam?
A:-Hardness
B:-Flexing resistance
C:-Compression set
D:-Tensile strength
Correct Answer:- Option-D
17. High VFA value of a latex compound indicate its
A:-Poor state of preservation
B:-Good state of preservation
C:-High level of Ammonia
D:-Low level of Ammonia
Correct Answer:- Option-A
18. The standard size of a mixing mill is
A:-7'' × 15''
B:-8'' × 24''
C:-6'' × 12''
D:-None of these
Correct Answer:- Option-C
19. Latex thread is manufactured by
A:-Dipping
B:-Extrusion
C:-Gelling
D:-Casting
Correct Answer:- Option-B
20. Identify the synthetic rubber that shows low gas permeability
A:-NR
B:-SBR
C:-IIR
D:-CR
Correct Answer:- Option-C
A:-Froathing agent
B:-Mould releasing agent
C:-Dispersing agent
D:-Plasticiser
Correct Answer:- Option-B
2. Magnesium ammonium sulphate is otherwise known as
A:-Slurry
B:-Serum
C:-Sludge
D:-None of the above
Correct Answer:- Option-C
3. Hardness is measured in
A:-MPa
B:-N/mm
C:-Shore A
D:-Poise
Correct Answer:- Option-C
4. Tripsometer is an instrument used to determine
A:-Abrasion resistance
B:-Cure time
C:-Rebound resilience
D:-Compression set
Correct Answer:- Option-C
5. Rubber hydrocarbon content of whole tyre reclaim
A:-50%
B:->50%
C:-<50%
D:-0%
Correct Answer:- Option-A
6. EBC is a form of
A:-Crumb rubber
B:-Crepe rubber
C:-Special purpose rubber
D:-Block rubber
Correct Answer:- Option-B
7. Which of the following property is best in mono-sulphidic vulcanisation systems?
A:-Heat resistance
B:-Fatigue resistance
C:-Tensile strength
D:-Modulus
Correct Answer:- Option-A
8. Schwratz value is a quality assessment of
A:-Latex foam
B:-Balloons
C:-Sponge
D:-Latex thread
Correct Answer:- Option-D
9. Which among these is not considered as a quality control test for latex?
A:-VFA
B:-N2 content
C:-Sludge content
D:-Ammonia content
Correct Answer:- Option-B
10. The equipment used for preparing dispersion
A:-Bal mill
B:-Ultrasonic mill
C:-Attrition mill
D:-All the above
Correct Answer:- Option-D
11. Identify the additive used as white pigment
A:-Titanium di oxide
B:-Clay
C:-Whiting
D:-Carbon black
Correct Answer:- Option-A
12. Metrolac is an equipment used to determine the
A:-TSC
B:-DRC
C:-MST
D:-VFA
Correct Answer:- Option-B
13. Which among these cannot be considered as a general purpose rubber?
A:-Styrene butadiene rubber
B:-Chloroprene rubber
C:-Butyl rubber
D:-Poly butadiene rubber
Correct Answer:- Option-A
14. Potassium Oleate is added to the latex compound to
A:-improve the tackiness
B:-increase the viscosity of latex
C:-stabilize the latex
D:-cheapen the latex
Correct Answer:- Option-C
15. Butyl rubber is cured with
A:-Sulphur
B:-Peroxides
C:-Metal oxides
D:-Dioximes
Correct Answer:- Option-D
16. Which of the following is not a quality test for latex foam?
A:-Hardness
B:-Flexing resistance
C:-Compression set
D:-Tensile strength
Correct Answer:- Option-D
17. High VFA value of a latex compound indicate its
A:-Poor state of preservation
B:-Good state of preservation
C:-High level of Ammonia
D:-Low level of Ammonia
Correct Answer:- Option-A
18. The standard size of a mixing mill is
A:-7'' × 15''
B:-8'' × 24''
C:-6'' × 12''
D:-None of these
Correct Answer:- Option-C
19. Latex thread is manufactured by
A:-Dipping
B:-Extrusion
C:-Gelling
D:-Casting
Correct Answer:- Option-B
20. Identify the synthetic rubber that shows low gas permeability
A:-NR
B:-SBR
C:-IIR
D:-CR
Correct Answer:- Option-C
21. Gelling agent used in foams
A:-Sodium alginate
B:-Sodium bi carbonate
C:-Sodium carbonate
D:-Sodium silico fluoride
Correct Answer:- Option-D
22. Which among these is not a coacervant?
A:-Ammonium nitrate
B:-Calcium chloride
C:-Calcium nitrate
D:-Acetic acid
Correct Answer:- Option-A
23. For the vulcanisation of chloroprene rubber the curing agent used is
A:-Sulphur
B:-Per oxide
C:-Metal oxide
D:-Radiational vulcanization
Correct Answer:- Option-C
24. Trans isomer of poly isoprene is
A:-Gutta purcha
B:-Isoprene
C:-Polybutadiene
D:-Buna-S
Correct Answer:- Option-A
25. The process of reusing the scrap in to products after chemical treatment is termed as
A:-Recycling
B:-Reclaiming
C:-Reusing
D:-Relaxing
Correct Answer:- Option-B
26. Necking or Pearling is a defect associated with
A:-Latex thread
B:-Latex foam
C:-Latex balloons
D:-All the above
Correct Answer:- Option-A
27. The bleaching agent used in Pale latex crepe
A:-Sodium sulfite
B:-Xylyl mercapton
C:-Thiokol
D:-Carbondisulphide
Correct Answer:- Option-B
28. Flat spotting of tyres usually occur in
A:-Steel chords
B:-Polyester chords
C:-Nylon chords
D:-Aramid chords
Correct Answer:- Option-C
29. The unit of tensile strength is
A:-N/m
B:-Kg/cm
C:-MPa
D:-%
Correct Answer:- Option-C
30. Which of the statement is not true about radial tyres?
A:-They have good cornering grip
B:-Good directional stability
C:-Low heat build up
D:-Low fuel consumption
Correct Answer:- Option-B
31. The slope of the stress-strain graph gives the
A:-Modulus
B:-Tensile strength
C:-Elongation at break
D:-Tear strength
Correct Answer:- Option-A
32. Monomers of butyl rubber are
A:-Isobutene, isoprene
B:-Isobutadiene, isoprene
C:-Isobutylene, isoprene
D:-Isobutylene, isobutadiene
Correct Answer:- Option-C
33. Friction ratio refers to
A:-Difference in roller speed
B:-Spacing between rollers
C:-Ratio of length to diameter of the rollers
D:-Difference in roller size
Correct Answer:- Option-A
34. Which is used as an anticoagulant?
A:-Ammonia
B:-Sodium sulfite
C:-Formalin
D:-All the above
Correct Answer:- Option-D
35. PAN, PBN etc are used in rubber compounding as
A:-Anti oxidant
B:-Anti ozonant
C:-Both
D:-Filler
Correct Answer:- Option-A
36. Which of the following property decreases with increase in crosslink density?
A:-Modulus
B:-Set
C:-Resilience
D:-Tensile strength
Correct Answer:- Option-B
37. A cellular product with closed cell structure
A:-Sponge
B:-Foam
C:-Both
D:-Micro cellular sheet
Correct Answer:- Option-D
38. EPNR stands for
A:-Ethylene propylene natural rubber
B:-Ethylene propylene diene rubber
C:-Epoxidised natural rubber
D:-Enzyme proteinated natural rubber
Correct Answer:- Option-C
39. In radial tyres chords are at what angle to the axis of rotation?
A:-60 degree
B:-120 degree
C:-30-40 degree
D:-90 degree
Correct Answer:- Option-D
40. The percentage of dirt in ISNR 5 is
A:-0.05%
B:-5%
C:-0.5%
D:-0.005%
Correct Answer:- Option-A
41. Which of these refers to determine the stability of latex on stirring?
A:-MST
B:-VFA
C:-KOH
D:-Sludge
Correct Answer:- Option-A
42. KOH is added to the latex compound as
A:-Emulsions
B:-Dispersion
C:-Suspension
D:-None of these
Correct Answer:- Option-D
43. Which is considered as cool running?
A:-Bias tyre
B:-Radial tyre
C:-Bias belted tyre
D:-All the above
Correct Answer:- Option-B
44. If the amount of sulphur is higher than that of the accelerator, the vulcanization system is a/an
A:-Efficient
B:-Semi efficient
C:-Open
D:-Conventional
Correct Answer:- Option-D
45. DRC% of field latex is
A:-30-40
B:-40-50
C:-50-60
D:-20-30
Correct Answer:- Option-A
46. Markham still apparatus is used to find
A:-DRC
B:-TSC
C:-VFA
D:-MST
Correct Answer:- Option-C
47. The delayed action accelerator used is
A:-MBT
B:-DPG
C:-CBS
D:-TMTD
Correct Answer:- Option-C
48. The test conducted to determine the level of proteins in latex is
A:-Total solid content
B:-Ammonia content
C:-Coagulum content
D:-Sludge content
Correct Answer:- Option-B
49. Product that is manufactured by wrapped mandrel moulding is
A:-Pipe
B:-Cable
C:-Belt
D:-Hose
Correct Answer:- Option-D
50. Which of the following is a continuous vulcanisation method?
A:-Auto clave curing
B:-Liquid curing
C:-Steam curing
D:-Batch curing
Correct Answer:- Option-B
51. The synthetic rubber with low resilience is
A:-NR
B:-PBR
C:-EPDM
D:-IIR
Correct Answer:- Option-D
52. FEF is a type of
A:-Reinforcing filler
B:-Accelerator
C:-Activator
D:-Flame retardant
Correct Answer:- Option-A
53. Accelerator for chloroprene rubber is
A:-MBTS
B:-TMTD
C:-Ethylene thiourea
D:-Mercapton
Correct Answer:- Option-C
54. Amount of inorganic content of a rubber is calculated from its
A:-Nitrogen content
B:-Ash content
C:-Magnesium content
D:-Coagulum content
Correct Answer:- Option-B
55. An example of a copolymer is
A:-Polybutadiene rubber
B:-Chloroprene rubber
C:-Nitrile rubber
D:-Silicone rubber
Correct Answer:- Option-C
56. The concentration method which works on stroke's formula is
A:-Centrifuging
B:-Electro decantation
C:-Creaming
D:-Evaporation
Correct Answer:- Option-C
57. Which is not used as an anticoagulant?
A:-Ammonia
B:-Sodium sulphite
C:-Boric acid
D:-Acetic acid
Correct Answer:- Option-D
58. The heating test done to detect halogens in a polymer is
A:-Muller's test
B:-Beilsetins test
C:-Webber test
D:-Miller's test
Correct Answer:- Option-B
59. With increase of filler loading the heat build up of a rubber compound
A:-Increases
B:-Decreases
C:-Increases and then decreases
D:-Neither increases nor decreases
Correct Answer:- Option-A
60. Balloons are prepared by dipping formers in
A:-Unvulcanised latex
B:-Vulcanised latex
C:-Prevulcanised latex
D:-Field latex
Correct Answer:- Option-C
61. For the production of hawai sole, natural rubber should be blended with
A:-Butyl rubber
B:-Styrene butadiene rubber
C:-Nitrile rubber
D:-EPDM
Correct Answer:- Option-B
62. High dosage of stearic acid is desirable in the compounding of which rubber product?
A:-Ebonite
B:-Sponge
C:-Door mat
D:-None of these
Correct Answer:- Option-B
63. Cells in latex foam are
A:-Partially opened and partially closed
B:-Completely open
C:-Closed
D:-Devoid of cells
Correct Answer:- Option-A
64. Renacit is a chemical name of a
A:-Filler
B:-Plasticiser
C:-Anti oxidant
D:-Peptiser
Correct Answer:- Option-D
65. Masterbatch is a
A:-Compounding ingredient
B:-Partially compounded rubber mix
C:-Compounded rubber mix
D:-Compounding equipment
Correct Answer:- Option-B
66. The accelerator used in latex compounding is
A:-MBT
B:-MBTS
C:-ZDC
D:-TMTD
Correct Answer:- Option-C
67. Fill factor is associated with
A:-Two roll mill
B:-Extruder
C:-Kneader
D:-Banburry machine
Correct Answer:- Option-D
68. Hollow articles are made by
A:-Compression moulding
B:-Injection moulding
C:-Transfer moulding
D:-Blow moulding
Correct Answer:- Option-D
69. The solvent for natural rubber is
A:-Cyclo hexane
B:-Chloroform
C:-Benzene
D:-Acetone
Correct Answer:- Option-D
70. The dimension of the extruded product as it comes out of the die will be
A:-Larger than the die diameter
B:-Smaller than the die diameter
C:-Same as the die
D:-Cannot be predicted
Correct Answer:- Option-A
71. Pot is used in
A:-Injection moulding
B:-Transfer moulding
C:-Compression moulding
D:-Blow moulding
Correct Answer:- Option-B
72. Friction ratio of a mixing mill
A:-1 : 2.5
B:-1 : 1.5
C:-1 : 1.25
D:-1 : 0.25
Correct Answer:- Option-C
73. De Lavel machine is used in
A:-Evaporation
B:-Creaming
C:-Electro decantation
D:-Centrifuging
Correct Answer:- Option-D
74. The grade of ISNR used in tyre industry
A:-ISNR 5
B:-ISNR 10
C:-ISNR 20
D:-ISNR 50
Correct Answer:- Option-C
75. Upside down mixing is recommended for
A:-CR
B:-EPDM
C:-SBR
D:-Silicone rubber
Correct Answer:- Option-B
76. The inorganic rubber among the following is
A:-Nitrile rubber
B:-Chloroprene rubber
C:-Butyl rubber
D:-Silicone rubber
Correct Answer:- Option-D
77. The percentage of ammonia in HA latex is
A:-0.6%
B:-0.9%
C:-0.3%
D:-0.4%
Correct Answer:- Option-A
78. Crack growth is minimum for
A:-SBR
B:-CR
C:-NR
D:-NBR
Correct Answer:- Option-C
79. CV rubber refers to
A:-Chemically viscous rubber
B:-Clear viscosity rubber
C:-Continuous vulcanized rubber
D:-Constant viscosity rubber
Correct Answer:- Option-D
80. Antimony oxide is an additive which imparts
A:-Heat resistance
B:-Flame resistance
C:-Conductivity
D:-Weather resistance
Correct Answer:- Option-B
A:-Sodium alginate
B:-Sodium bi carbonate
C:-Sodium carbonate
D:-Sodium silico fluoride
Correct Answer:- Option-D
22. Which among these is not a coacervant?
A:-Ammonium nitrate
B:-Calcium chloride
C:-Calcium nitrate
D:-Acetic acid
Correct Answer:- Option-A
23. For the vulcanisation of chloroprene rubber the curing agent used is
A:-Sulphur
B:-Per oxide
C:-Metal oxide
D:-Radiational vulcanization
Correct Answer:- Option-C
24. Trans isomer of poly isoprene is
A:-Gutta purcha
B:-Isoprene
C:-Polybutadiene
D:-Buna-S
Correct Answer:- Option-A
25. The process of reusing the scrap in to products after chemical treatment is termed as
A:-Recycling
B:-Reclaiming
C:-Reusing
D:-Relaxing
Correct Answer:- Option-B
26. Necking or Pearling is a defect associated with
A:-Latex thread
B:-Latex foam
C:-Latex balloons
D:-All the above
Correct Answer:- Option-A
27. The bleaching agent used in Pale latex crepe
A:-Sodium sulfite
B:-Xylyl mercapton
C:-Thiokol
D:-Carbondisulphide
Correct Answer:- Option-B
28. Flat spotting of tyres usually occur in
A:-Steel chords
B:-Polyester chords
C:-Nylon chords
D:-Aramid chords
Correct Answer:- Option-C
29. The unit of tensile strength is
A:-N/m
B:-Kg/cm
C:-MPa
D:-%
Correct Answer:- Option-C
30. Which of the statement is not true about radial tyres?
A:-They have good cornering grip
B:-Good directional stability
C:-Low heat build up
D:-Low fuel consumption
Correct Answer:- Option-B
31. The slope of the stress-strain graph gives the
A:-Modulus
B:-Tensile strength
C:-Elongation at break
D:-Tear strength
Correct Answer:- Option-A
32. Monomers of butyl rubber are
A:-Isobutene, isoprene
B:-Isobutadiene, isoprene
C:-Isobutylene, isoprene
D:-Isobutylene, isobutadiene
Correct Answer:- Option-C
33. Friction ratio refers to
A:-Difference in roller speed
B:-Spacing between rollers
C:-Ratio of length to diameter of the rollers
D:-Difference in roller size
Correct Answer:- Option-A
34. Which is used as an anticoagulant?
A:-Ammonia
B:-Sodium sulfite
C:-Formalin
D:-All the above
Correct Answer:- Option-D
35. PAN, PBN etc are used in rubber compounding as
A:-Anti oxidant
B:-Anti ozonant
C:-Both
D:-Filler
Correct Answer:- Option-A
36. Which of the following property decreases with increase in crosslink density?
A:-Modulus
B:-Set
C:-Resilience
D:-Tensile strength
Correct Answer:- Option-B
37. A cellular product with closed cell structure
A:-Sponge
B:-Foam
C:-Both
D:-Micro cellular sheet
Correct Answer:- Option-D
38. EPNR stands for
A:-Ethylene propylene natural rubber
B:-Ethylene propylene diene rubber
C:-Epoxidised natural rubber
D:-Enzyme proteinated natural rubber
Correct Answer:- Option-C
39. In radial tyres chords are at what angle to the axis of rotation?
A:-60 degree
B:-120 degree
C:-30-40 degree
D:-90 degree
Correct Answer:- Option-D
40. The percentage of dirt in ISNR 5 is
A:-0.05%
B:-5%
C:-0.5%
D:-0.005%
Correct Answer:- Option-A
41. Which of these refers to determine the stability of latex on stirring?
A:-MST
B:-VFA
C:-KOH
D:-Sludge
Correct Answer:- Option-A
42. KOH is added to the latex compound as
A:-Emulsions
B:-Dispersion
C:-Suspension
D:-None of these
Correct Answer:- Option-D
43. Which is considered as cool running?
A:-Bias tyre
B:-Radial tyre
C:-Bias belted tyre
D:-All the above
Correct Answer:- Option-B
44. If the amount of sulphur is higher than that of the accelerator, the vulcanization system is a/an
A:-Efficient
B:-Semi efficient
C:-Open
D:-Conventional
Correct Answer:- Option-D
45. DRC% of field latex is
A:-30-40
B:-40-50
C:-50-60
D:-20-30
Correct Answer:- Option-A
46. Markham still apparatus is used to find
A:-DRC
B:-TSC
C:-VFA
D:-MST
Correct Answer:- Option-C
47. The delayed action accelerator used is
A:-MBT
B:-DPG
C:-CBS
D:-TMTD
Correct Answer:- Option-C
48. The test conducted to determine the level of proteins in latex is
A:-Total solid content
B:-Ammonia content
C:-Coagulum content
D:-Sludge content
Correct Answer:- Option-B
49. Product that is manufactured by wrapped mandrel moulding is
A:-Pipe
B:-Cable
C:-Belt
D:-Hose
Correct Answer:- Option-D
50. Which of the following is a continuous vulcanisation method?
A:-Auto clave curing
B:-Liquid curing
C:-Steam curing
D:-Batch curing
Correct Answer:- Option-B
51. The synthetic rubber with low resilience is
A:-NR
B:-PBR
C:-EPDM
D:-IIR
Correct Answer:- Option-D
52. FEF is a type of
A:-Reinforcing filler
B:-Accelerator
C:-Activator
D:-Flame retardant
Correct Answer:- Option-A
53. Accelerator for chloroprene rubber is
A:-MBTS
B:-TMTD
C:-Ethylene thiourea
D:-Mercapton
Correct Answer:- Option-C
54. Amount of inorganic content of a rubber is calculated from its
A:-Nitrogen content
B:-Ash content
C:-Magnesium content
D:-Coagulum content
Correct Answer:- Option-B
55. An example of a copolymer is
A:-Polybutadiene rubber
B:-Chloroprene rubber
C:-Nitrile rubber
D:-Silicone rubber
Correct Answer:- Option-C
56. The concentration method which works on stroke's formula is
A:-Centrifuging
B:-Electro decantation
C:-Creaming
D:-Evaporation
Correct Answer:- Option-C
57. Which is not used as an anticoagulant?
A:-Ammonia
B:-Sodium sulphite
C:-Boric acid
D:-Acetic acid
Correct Answer:- Option-D
58. The heating test done to detect halogens in a polymer is
A:-Muller's test
B:-Beilsetins test
C:-Webber test
D:-Miller's test
Correct Answer:- Option-B
59. With increase of filler loading the heat build up of a rubber compound
A:-Increases
B:-Decreases
C:-Increases and then decreases
D:-Neither increases nor decreases
Correct Answer:- Option-A
60. Balloons are prepared by dipping formers in
A:-Unvulcanised latex
B:-Vulcanised latex
C:-Prevulcanised latex
D:-Field latex
Correct Answer:- Option-C
61. For the production of hawai sole, natural rubber should be blended with
A:-Butyl rubber
B:-Styrene butadiene rubber
C:-Nitrile rubber
D:-EPDM
Correct Answer:- Option-B
62. High dosage of stearic acid is desirable in the compounding of which rubber product?
A:-Ebonite
B:-Sponge
C:-Door mat
D:-None of these
Correct Answer:- Option-B
63. Cells in latex foam are
A:-Partially opened and partially closed
B:-Completely open
C:-Closed
D:-Devoid of cells
Correct Answer:- Option-A
64. Renacit is a chemical name of a
A:-Filler
B:-Plasticiser
C:-Anti oxidant
D:-Peptiser
Correct Answer:- Option-D
65. Masterbatch is a
A:-Compounding ingredient
B:-Partially compounded rubber mix
C:-Compounded rubber mix
D:-Compounding equipment
Correct Answer:- Option-B
66. The accelerator used in latex compounding is
A:-MBT
B:-MBTS
C:-ZDC
D:-TMTD
Correct Answer:- Option-C
67. Fill factor is associated with
A:-Two roll mill
B:-Extruder
C:-Kneader
D:-Banburry machine
Correct Answer:- Option-D
68. Hollow articles are made by
A:-Compression moulding
B:-Injection moulding
C:-Transfer moulding
D:-Blow moulding
Correct Answer:- Option-D
69. The solvent for natural rubber is
A:-Cyclo hexane
B:-Chloroform
C:-Benzene
D:-Acetone
Correct Answer:- Option-D
70. The dimension of the extruded product as it comes out of the die will be
A:-Larger than the die diameter
B:-Smaller than the die diameter
C:-Same as the die
D:-Cannot be predicted
Correct Answer:- Option-A
71. Pot is used in
A:-Injection moulding
B:-Transfer moulding
C:-Compression moulding
D:-Blow moulding
Correct Answer:- Option-B
72. Friction ratio of a mixing mill
A:-1 : 2.5
B:-1 : 1.5
C:-1 : 1.25
D:-1 : 0.25
Correct Answer:- Option-C
73. De Lavel machine is used in
A:-Evaporation
B:-Creaming
C:-Electro decantation
D:-Centrifuging
Correct Answer:- Option-D
74. The grade of ISNR used in tyre industry
A:-ISNR 5
B:-ISNR 10
C:-ISNR 20
D:-ISNR 50
Correct Answer:- Option-C
75. Upside down mixing is recommended for
A:-CR
B:-EPDM
C:-SBR
D:-Silicone rubber
Correct Answer:- Option-B
76. The inorganic rubber among the following is
A:-Nitrile rubber
B:-Chloroprene rubber
C:-Butyl rubber
D:-Silicone rubber
Correct Answer:- Option-D
77. The percentage of ammonia in HA latex is
A:-0.6%
B:-0.9%
C:-0.3%
D:-0.4%
Correct Answer:- Option-A
78. Crack growth is minimum for
A:-SBR
B:-CR
C:-NR
D:-NBR
Correct Answer:- Option-C
79. CV rubber refers to
A:-Chemically viscous rubber
B:-Clear viscosity rubber
C:-Continuous vulcanized rubber
D:-Constant viscosity rubber
Correct Answer:- Option-D
80. Antimony oxide is an additive which imparts
A:-Heat resistance
B:-Flame resistance
C:-Conductivity
D:-Weather resistance
Correct Answer:- Option-B